New Carburetor for Briggs & Stratton Vanguard 4-stroke 845273 845032 844172√
$ 34.34
Description
Item Specification Condition: 100% Brand New and High Quality. Replacement Part Number: 845032,844172,842097,611477,613477 Compatible Models: For Briggs & Stratton 845273 Carburetor Package Included: Carburetor as Pictured The installation steps for a carburetor can generally be followed in the order below: 1. Check the Carburetor and Accessories Before installation, check the carburetor and related components for any damage, wear, or contamination to ensure they are in good condition. 2. Cleaning Clean the surface where the carburetor will be installed, as well as the intake manifold, to ensure there is no dust or debris that could affect the proper functioning of the carburetor. 3. Remove the Old Carburetor Before removing the old carburetor, disconnect the power (if there is an electronic control system) and fuel lines, and turn off the engine. Detach the intake and exhaust hoses from the carburetor, which are typically located at the bottom or side of the carburetor. Remove the securing screws, usually Allen screws or flathead screws (use a specialized carburetor screwdriver). Carefully lift the carburetor to separate it from the engine, taking care not to damage it. 4. Install the New Carburetor Position the new carburetor in its original place, ensuring it is properly aligned with the intake manifold or intake port. Be sure the intake and exhaust ports are installed correctly (not reversed), and then tighten the securing screws. 5. Connect the Fuel Line Attach the fuel line to the fuel inlet of the carburetor, ensuring that the connection is tight to avoid fuel leakage. Check the fuel line for signs of aging or damage; if any is found, replace it. 6. Secure the Carburetor Use bolts to secure the carburetor to the intake manifold or the appropriate position, ensuring it is firmly in place without any wobbling. 7. Check the Electronic Control System (if applicable) If the carburetor has an electronic control system (such as an automatic throttle control), connect the cables or wires, ensuring all electrical connections are secure and correct. 8. Adjust the Carburetor Adjust the fuel/air mixture, idle speed, and other tuning screws according to the vehicle or equipment requirements to ensure smooth operation. 9. Check the Cylinders and Exhaust System After installing the carburetor, ensure there are no air leaks in the intake system, that the cylinders are functioning properly, and that the exhaust system is clear. 10. Test the Engine Open the throttle, start the engine, and observe the operation of the carburetor. Check for any unusual noise, fuel leakage, or stalling. Make fine adjustments if necessary. 11. Final Check Inspect all connection points, including the fuel lines, cables, and bolts, to ensure they are tightened properly and there are no loose connections or leaks. These steps are generally applicable to carburetor installations. Specific details should be referenced in the carburetor's installation manual or the manufacturer's instructions. Includes: 1 X Carburetor 1 x Fuel Filter 1 x Cleaning Tool 2 x Gaskets
Good quality parts for a Nikki carburetor, new condition in excellent packaging, excellent value because it was shipped out right away and arrived two days later, 3 days earlier than expected. Item was stored indoors and has a new appearance as well.
Shipping took way too long. Item received was not the offset wrench as pictured. Returned after much back & forth with seller. Thanks eBay, for the money back guarantee!
Fast order and a hiccup. Seller made things right with A refund when my order got delivered to wrong address.
Related products
NEW A021002560 A021002540 Carburetor For Shindaiwa B450 Brush Cutter
$ 15.455LK890 5/8" x 89" Lawn Mower Deck Belt Replacement, Gray
$ 14.51635-7033-00 12V Deck Lift Actuator For Bad Boy Lawn Mower ZT Elite CZT Maverick
$ 79.15Replacement Fuel Solenoid Fit for Briggs Stratton Engines Part 692094 807664
$ 7.09